30MPa Air Compressor Pump 110V PCP Electric 4500PSI High Pressure System Rifle^

  

30MPa Air Compressor Pump 110V PCP Electric 4500PSI High Pressure System R-ifle. Take out the product; install the hose at the air outlet. Note: gasket is needed, or air leakage might exist. Connect 2 cold water pipes and connect them to the water pump. Note: the lower pipe connected to the water pump is water inlet; sinking pump is used in this product.

The water pump should be immersed in water for using. Install the pressure relief v-alve screw; pressure relief v-alve screw is installed at the pressure relief hole under the hose. The blow-down v-alve is installed at the. Drain outlet of the first air chamber block.

Immerse the water pump in water and switch on the power. Connect the container need to be inflated, make sure the connection is correct. Screw up the screws of the blow-down v-alve and pressure relief v-alve.

Switch on the power ant the machine operates. Note: when the machine is operating, the water must operate correspondingly, or the product might be damaged due to overheated, personal harm may even occur. After the inflation is completed, screw of the pressure relief v-alve should be firstly loosen, then the power is to be switched off, by doing so, high pressure. Air backlash caused due to sudden failure of power supply would be avoided, which could lengthen l-ifetime of the product, as well as discharge high pressure air in the machine.

Please use the power supply according to the parameter table. If abnormal noise occurred during the using of the product, please stop using it instantly and check the cause.

The product should be placed at a place that it couldn t be t-ouched by children. Please do not use it in moist and f-lammable place. Please do not modify it arbitrarily, disassembling and repair by non-technical personnel is not allowed.

Make sure the socket could withstand a currentgreater than 8A before using it, or the circuit might be burnt, the product might be damaged and the dangers may be caused due to overload of the socket. Please do not t-ouch the head section after the machine was just being used, so as to not beburnt by high temperature.

Please do not leave without authorized, or the product might be damaged by increasingly rising pressure, sustained overload motor, even halt due to the operation pressure has reached but it is not turned off timely. When it is used for inflating slightly larger container, the cooling water should be changed every 30 minutes, in this way, the cylinder. Temperature could be better controlled.

The machine oil should be checked regularly, make sure the oil level is above the upper edge of the red point. If color of machine oil becomes dark and black, it should be changed in time. ISO VG46 or AW 46. We are not responsible for the package lost due to incorrect address.

If you can't get your items in time, please contact to us first, we will check and solve it for you soon. Sometimes have a little delay due to the weekend or holiday. SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays.

Transit times may vary, particularly during the holiday season. Thank you very much for your interest in our products and browsing the details of the products. The product provided by my. All high quality and carefully selected. If the goods you receive are unqualified in quality.

Please contact me with no hesitation. I will try my best to satisfy you. What's more, compared with other commodities in the market, our products have a certain. Of course, we will offer a certain amount of. Our company has two warehouses in the East and west of the United States. Different commodities correspond to different logistics prices. This depends on your geographical location. If you think the logistics prices of commodities in our stores are too high, you can consult me at any time! Hope you a nice day!

Air compressor cooling system: Ultra-efficient cooling system to avoid high temperature damagefor better protection of the head. Stainless steel booster heat sink reduces exhaust air temperature. Plastic-coated for safety and waterproof performance. Stainless steel high pressure tank, machine body is made of aluminum alloy and brass. Adjustable pressure, pre-set pressure (the machine stops once the preset pressure is reached), support free pressure setting, preset pressure value, the machine will automatically close when the pressure is reached.

In addition, once the pressure reaches 30MPA / 300bar, the machine also will automatically shut down. Please note: once you stop working, do not. The head of the machine to prevent burns. Widely Used: Perfect for Gas cylinders, Airguns, fire fighting, paintball, leakage detecting, pressure-tight test, automobiles, air impermeability test, pressure proof test, etc.

Attention:The airgun compressor must be working with oil, so you must pay attention to the level of oil. Working Pressure: 300BAR / 30MPA/ 4500PSI. Inflating Speed: 2800 r / min. Filling Time: 1L/ 10 minutes.

Size: 14.2 x 7.1 x 14.6. 1 x Air Compressor Pump. 1 x 8mm Quick Connector. 1 x Water Cooling Pump.

1 x Tire Inflation Adapter. 1 x Power Cables (110V). (1) Keep this item out of childrens reach.

(2)Do not use this product in humid or inflammable places. (3)Unauthorized detachment & repair is not recommended. (4)Make sure your socket can withstand over 8 A electric current, or the circuit may get burnt.

(5)To prevent scald, do not. The head of the machine once it stops working. (6)The machine will auto shut off once the pressure reaches 30MPA / 300bar. (7)To keep the cylinder stator temperature in control, please change the cooling water every 30 minutes.

(8)Regularly check the engine oil and make sure oil level stays above the red dot; change engine oil if oil color turns. (9) You can preset the pressure value, the machine will automatically shut down when the pressure is reached. The item "30MPa Air Compressor Pump 110V PCP Electric 4500PSI High Pressure System Rifle^" is in sale since Friday, December 3, 2021. This item is in the category "Home & Garden\Tools & Workshop Equipment\Air Tools & Air Compressors\Air Compressors".

The seller is "kamyo-50" and is located in New JerseyCalifornia. This item can be shipped to United States.

• Brand: Unbranded
• Type: Pancake Air Compressor
• Voltage: 110 V
• Power Source: Corded Electric
• MPN: Does Not Apply
• 1.8KW: 1.8KW
• Working Pressure: 300BAR / 30MPA/ 4500PSI
• Displacement: 80L/min
• Material: Alloy
• Inflating Speed: 2800 r / min
• Noise: 78 decibel (Max.)
• Suction Pressure: Atmospheric Pressure
• Filling Time: 1L/ 10 minutes
• Cooling System: Water
• Size: 14.2 x 7.1 x 14.6
• Weight: 17kg