110V 30MPa PCP Electric 4500PSI High Pressure System Rifle Air Compressor Pump

  

30MPa Air Compressor Pump 110V PCP Electric 4500PSI High Pressure. The product should be placed at a place that it couldnt be touched by children.

Please do not use it in moist and flammable place. Please do not modify it arbitrarily, disassembling and repair by non-technical personnel is not allowed. Make sure the socket could withstand a current greater than 8A before using it, or the circuit might be burnt, the product might be damaged and the dangers may be caused due to overload of the socket. Please do not touch the head section after the machine was just being used, so as to not be burnt by high temperature. Please do not leave without authorized, or the product might be damaged by increasingly rising pressure, sustained overload motor, even halt due to the operation pressure has reached but it is not turned off timely. When it is used for inflating slightly larger container, the cooling water should be changed every 30 minutes, in this way, the cylinder temperature could be better controlled. The machine oil should be checked regularly, make sure the oil level is above the upper edge of the red point. If color of machine oil becomes dark and black, it should be changed in time.

1 x High Pressure 30Mpa Electric Compressor Pump. User Manual(Before using, please read the Notice and Manual strictly). I: Please strictly follow this operating instructions for operation and use, otherwise it will cause the machine not to be used normally and damage the machine. Check/add oil above the red dot.

Replace the breathing plug in the circle with the transport plug on the machine. Loosen the high pressure relief valve and the low pressure relief valve. Remember that the machine is unscrewed before start-up because the machine is starting with zero pressure. If it is not loosened, it will not start.

After starting the machine, it will be tightened. When the inflator reaches the required pressure, loosen the pressure relief valve first, and then press the power off. Turn on the air pump power, start using. II:The installation method of separating water and oil. Unscrew hose and female head.

Remove the separator and a white gasket inside the bag. Place the white gasket into the tapped hole in the separator. (White gasket must be installed, otherwise it will not be sealed, there is leakage phenomenon). Properly tightened to complete the installation. Check if the pressure relief valve is loose. Check if the overload protection function is activated.

(Press the button in the figure below). Check if the motor's foot is damaged by transportation. After power off, stir the fan with a screwdriver to turn the machine. If the above methods are tried but still not started, you could try the following method: removing the low pressure check valve. Be sure to follow the installation sequence when installing.

The machine is equipped with an emergency high-pressure explosion-proof valve. The working principle is when the working pressure of the machine exceeds 30mpa, a very thin piece of copperr will be broken due to pressure.

The broken copper piece cannot be repaired. At this time, a new one needs to be replaced. The following figure shows the location of the explosion-proof valve.

Unscrew the explosion-proof valve screw. Insert the explosion-proof valve and tighten the explosion-proof valve screw. The machine can start normally but it cannot achieve higher pressure.

At this time, the high pressure check valve needs to be cleaned. Clean up method Wrench loosen check valve screw. Remove the check valve and start the machine for 5 minutes. Clean the check valve hole and replace the check valve.

Check valve installation sequence close-up. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Used items will not be accepted for return. Thanks for coming to my store.

We will reply you ASAP. Our aim is to provide Top Level Customer Service, so we will try our best to solve any problem. The item "110V 30MPa PCP Electric 4500PSI High Pressure System Rifle Air Compressor Pump" is in sale since Tuesday, April 30, 2019. This item is in the category "Business & Industrial\Hydraulics, Pneumatics, Pumps & Plumbing\Pumps & Pump Accessories\Other Pumps". The seller is "khairulabdh_0" and is located in Monroe Township, New Jersey.

This item can be shipped to United States.

• Type: High Pressure
• MPN: Does Not Apply
• Brand: Unbranded
• Introduction:: CA&NJ
• size: 36* 18 * 37CM/14.2*7.1*14.6 INCH( L * W * H)
• Air flow rate: 40-50L/MIN, 1.5-1.8CFM
• Motor Power: 1.8KW
• Working Pressure: 100-300BAR,1500- 4500PSI
• Power: 110V 60HZ
• Model: 30Mpa
• Cooling System: Water Cooling
• Displacement: 80L/min
• Material: Alloy
• Inflating Speed: 2800 r / min
• Noise: 78 decibel (Max.)
• Suction Pressure: Atmospheric Pressure
• Filling Time: 1L/ 10 minutes
• Net Weight: 16.2KG/35.72Lbs
• Power Source: Electric
• warranty: 2 years