Please do not use it in moist and flammable place. Please do not modify it arbitrarily, disassembling and repair by non-technical personnel is not allowed.
Make sure the socket could withstand a current greater than 8A before using it, or the circuit might be burnt, the product might be damaged and the dangers may be caused due to overload of the socket. Please do not touch the head section after the machine was just being used, so as to not be burnt by high temperature. Please do not leave without authorized, or the product might be damaged by increasingly rising pressure, sustained overload motor, even halt due to the operation pressure has reached but it is not turned off timely. When it is used for inflating slightly larger container, the cooling water should be changed every 30 minutes, in this way, the cylinder temperature could be better controlled. The machine oil should be checked regularly, make sure the oil level is above the upper edge of the red point.If color of machine oil becomes dark and black, it should be changed in time. Take out the product; install the hose at the air outlet. Note: gasket is needed, or air leakage might exist.
Connect 2 cold water pipes and connect them to the water pump. Note: the lower pipe connected to the water pump is water inlet; sinking pump is used in this product. The water pump should be immersed in water for using. Install the pressure relief valve screw; pressure relief valve screw is installed at the pressure relief hole under the hose. The blow-down valve is installed at the.
Drain outlet of the first air chamber block. Immerse the water pump in water and switch on the power. Connect the container need to be inflated, make sure the connection is correct.Screw up the screws of the blow-down valve and pressure relief valve. Switch on the power ant the machine operates. Note: when the machine is operating, the water must operate correspondingly, or the product might be damaged due to overheated, personal harm may even occur. After the inflation is completed, screw of the pressure relief valve should be firstly loosen, then the power is to be switched off, by doing so, high pressure. Air backlash caused due to sudden failure of power supply would be avoided, which could lengthen lifetime of the product, as well as discharge high pressure air in the machine. 46 wear resistant hydraulic oil. If the machine vibrates violently, please add pad or towel under the compressor.
The compressor working, the cooling system can be working at the same time. The machine must be working with oil, so you must pay attention to the level of oil. Size: 34 18 37CM/22.214.171.124 INCH(L W H). Net Weight: 16.2KG/35.72LBS. Air flow rate: 50L/MIN(13.2GPM).Working Pressure: 300BAR 30MPA 4500PSI. 1 x Electric Compressor Pumpwith one plug.
1 x Female Head 8 mm High Pressure Hose. 2 x Inlet & Outlet Water Pipe.1 x Water Pump With Sucker Regulator. 1 x Oil Breathing Nozzle. 1 x Suit of Seal Rings. Feedback is very important to us.
It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately.If it's non-workdays, please kindly be patient and wait till Monday. High Pressure Electric Compressor Pump PCP Electric Air Pump 30MPA/4500PSI/300ba Specifications: Material: All Copper Motor Voltage: 110 V / 60Hz Current: 16 A Motor Power: 1.8 KW Working Pressure: Max 300bar/30Mpa/4500PSI Air Flow Rate: 50 L/min Revolving Speed: 2800 r/min Noise: 78 DBMax Cooling System: Water Cooling/Air Cooling SizeLWH34 x 18 x 37 cm/13.4" x 7" x 14.5 Plug: US Plug Power Line Length: 1.5 M Lubrication Mode: Splash Type Compression Stage: Two Stage Package Weight: 17 KG Main Scope of Application: Automobile, Diving Bottle, Industrial Bottle Features: 1. Use imported super wear piston ring. Integral cylinder head without external gas path pipe.
Package Included: 1 x Electric Compressor Pumpwith one plug. The item "Electric High Pressure Pump 30MPa Air Compressor System Rifle PCP Air Gun New" is in sale since Tuesday, October 24, 2017. This item is in the category "Business & Industrial\Hydraulics, Pneumatics, Pumps & Plumbing\Pumps & Pump Accessories\Other Pumps". The seller is "medshop888" and is located in Dayton, New Jersey. This item can be shipped to United States.